logo
Shenzhen Wisdomlong Technology CO.,LTD
উদ্ধৃতি

ABB Drive Control Units RDCU02C Inverter Control Unit

পণ্যের বিবরণ:
উৎপত্তি স্থল: সুইডেন
পরিচিতিমুলক নাম: ABB
মডেল নম্বার: RDCU02C
বিস্তারিত তথ্য
উৎপত্তি স্থল:
সুইডেন
পরিচিতিমুলক নাম:
ABB
মডেল নম্বার:
RDCU02C
ব্র্যান্ড:
এবিবি
মডেল:
RDCU02C
ওজন:
0.8 কেজি
পণ্যের নাম:
আই/ও মডিউল
ওয়ারেন্টি:
12 মাস
অপ্রয়োজনীয়তা:
না
সার্ভো মডিউল:
ড্রাইভ কন্ট্রোল ইউনিট
অবস্থা:
নতুন
সীসা সময়:
স্টক
মূল দেশ:
সুইডেন
বিশেষভাবে তুলে ধরা:

High Light

বিশেষভাবে তুলে ধরা:

ABB inverter control unit RDCU02C

,

PLC drive control unit

,

programmable logic controller with warranty

ট্রেডিং তথ্য
ন্যূনতম চাহিদার পরিমাণ:
1
মূল্য:
আলোচনাযোগ্য
প্যাকেজিং বিবরণ:
আসল বাক্সে নতুন
ডেলিভারি সময়:
2-3 কাজের দিন
পরিশোধের শর্ত:
টিটি পশ্চিম ইউনিয়ন
যোগানের ক্ষমতা:
100
পণ্যের বর্ণনা
ABB Drive Control Units RDCU02C Inverter Control Unit
TYPE DESCRIPTION
Manufacturer ABB
Part Number/MPN RDCU-02C
Category Controllers, Automation Parts
Condition Brand New
Input Voltage 415v
Input Phase 3 Phase
Input Frequency 50HZ
Wiring

General

The shields of the I/O cables should be grounded to the chassis of the cubicle as close to the RDCU as possible.

Use grommets at all cable entries.

Handle fibre optic cables with care. When unplugging fibre optic cables, always grab the connector, not the cable itself. Do not touch the ends of the fibres with bare hands as the fibre is extremely sensitive to dirt.

The maximum long-term tensile load for the fibre optic cables included is 1 N; the minimum short-term bend radius is 25 mm (1”).

Digital/Analogue input/output connections

See the Firmware Manual of the application program in question.

Installation of optional modules

Follow the instructions given in the user manual of the module.

Other connections

See also the wiring diagram below.

Powering the RDCU

The RDCU is powered through connector X34. The unit can be powered from the power supply board of the inverter (or IGBT supply) module, provided that the maximum current of 1 A is not exceeded.

The RDCU can also be powered from an external 24 V DC supply. Note also that the current consumption of the RDCU is dependent on the optional modules attached. (For current consumption of optional modules, see their respective user manuals.)

Fibre optic connection to inverter/IGBT supply module

Connect the PPCS link of the AINT (ACS 800 series modules) board of the inverter (or IGBT supply) module to fibre optic connectors V57 and V68 of the RDCU.

Note: The recommended maximum distances for the fibre optic link is 10 m (for plastic [POF] cable). In case longer distances are required, contact an ABB representative.

ABB Drive Control Units   RDCU02C Inverter Control Unit  0
Contact Information
Contact Person: Anna
Phone: +0086-13534205279